Arduino MKR Fox 1200 Developer Board
Arduino MKR Fox 1200 Developer Board overview
The Arduino MKR Fox 1200 Developer Board is an electronic component. Main ratings: Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU; Board Power Supply 5V; Supported Batteries 2x AA or AAA; Circuit Operating Voltage 3.3V. This page brings together the Arduino MKR Fox 1200 Developer Board pinout and key specifications, with the full datasheet PDF to preview below or download.
The Arduino MKR FOX 1200 is a powerful board that combines the functionality of the Zero and SigFox connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. Arduino MKR Fox 1200 design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32-bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software (IDE) for code development and programming.
Arduino MKR Fox 1200 is the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power (5V) to the board. The board is able to run with or without batteries connected and has limited power consumption.
Key specifications
Datasheet
Arduino MKR Fox 1200 Developer Board features
- 32-bit computational power
- Rich set of I/O interfaces
- Low power SigFox communication
- Microchip SAMD21 32-bit Arm® Cortex®-M0+ Microcontroller
- Atmel ATA8520 single-chip Sigfox RF transmitter module
- Includes a free subscription to the Sigfox network and Spot’it Geolocation Service
- Automatic switch between the two sources
Arduino MKR Fox 1200 Developer Board pinout
| Pin | Name | Description |
|---|---|---|
| 1 | AREF | Analog Reference Voltage |
| 2 | D15 / A0 | Digital I/O 15 / Analog I/O 0 |
| 3 | D16 / A1 | Digital I/O 16 / Analog I/O 1 |
| 4 | D17 / A2 | Digital I/O 17 / Analog I/O 2 |
| 5 | D18 / A3 | Digital I/O 18 / Analog I/O 3 |
| 6 | D19 / A4 | Digital I/O 19 / Analog I/O 4 |
| 7 | D20 / A5 | Digital I/O 20 / Analog I/O 5 |
| 8 | D21 / A6 | Digital I/O 21 / Analog I/O 6 |
| 9 | D0 | Digital I/O 0 |
| 10 | D1 | Digital I/O 1 |
| 11 | D2 | Digital I/O 2 |
| 12 | D3 | Digital I/O 3 |
| 13 | D4 | Digital I/O 4 |
| 14 | D5 | Digital I/O 5 |
| 15 | D6 | Digital I/O 6 |
| 16 | D7 | Digital I/O 7 |
| 17 | D8 | Digital I/O 8 |
| 18 | D9 | Digital I/O 9 |
| 19 | D10 | Digital I/O 10 |
| 20 | D11 | Digital I/O 11 |
| 21 | D12 | Digital I/O 12 |
| 22 | D13 | Digital I/O 13 |
| 23 | D14 | Digital I/O 14 |
| 24 | RESET | Reset Pin |
Show all 28 pins
| Pin | Name | Description |
|---|---|---|
| 25 | GND | Ground Pin |
| 26 | +3V3 | Chip Supply voltage (+3.3V) |
| 27 | Vin | Voltage Input |
| 28 | +5v | Chip Supply Voltage (+5V) |
Arduino MKR Fox 1200 Developer Board specifications
| Microcontroller | SAMD21 Cortex-M0+ 32bit low power ARM MCU |
|---|---|
| Board Power Supply (USB/VIN) | 5V |
| Supported Batteries(*) | 2x AA or AAA |
| Circuit Operating Voltage | 3.3V |
| Digital I/O Pins | 8 |
| PWM Pins | 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19) |
| UART | 1 |
| SPI | 1 |
| I2C | 1 |
| Analog Input Pins | 7 (ADC 8/10/12 bit) |
| Analog Output Pins | 1 (DAC 10 bit) |
| External Interrupts | 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17) |
| DC Current per I/O Pin | 7 mA |
| Flash Memory | 256 KB |
| SRAM | 32 KB |
| Clock Speed | 32.768 kHz (RTC), 48 MHz |
| LED_BUILTIN | 6 |
| LED_BUILTIN | 6 |
| Antenna power | 2dB |
| Carrier frequency | 868 MHz |
| Length | 67.64 mm |
| Width | 25 mm |
| Weight | 32 gr. |
Comments 0
Leave a comment