BQ24727 Datasheet – Battery SMBus Charge Controller
BQ24727 overview
The BQ24727 is a Battery SMBus Charge Controller made by Texas Instruments, supplied in a QFN-20 Type package. The absolute maximum ratings table on this page lists the 4 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the BQ24727 pinout and maximum ratings, with the full datasheet PDF to preview below or download.
The bq24707 and bq24707A devices are high-efficiency, synchronous battery chargers, offering low component count for space-constrained, multi chemistry battery charging applications.
SMBus controlled input current, charge current, and charge voltage DACs allow for very high regulation accuracies that can be easily programmed by the system power management micro-controller.
The IC uses the internal input current register or external ILIM pin to throttle down PWM modulation to reduce the charge current.
The IC provides an IFAULT output to alarm if any MOSFET fault or input over current occurs. This selectors when the fault occurs. Meanwhile, an independent comparator with internal reference is available to monitor input current, output current, or output voltage.
The IC charges one-, two-, three-, or four-series Li+ cells, and is available in a 20-pin, 3.5 × 3.5 mm QFNIntegrated Soft-Start package.
Datasheet
BQ24727 features
- SMBus Host-Controlled NMOS-NMOS Synchronous Buck Converter With Programmable 615 kHz, 750 kHz, and 885 kHz Switching Frequency
- Real-Time System Control on ILIM Pin to Limit Charge Current
- Enhanced Safety Features for Overvoltage system power management micro-controller. Protection, Overcurrent Protection, Battery, and MOSFET Short-Circuit Protection
- ±0.5% Charge Voltage Accuracy up to 19.2 V
- ±3% Charge Current Accuracy up to 8.128 A
- ±3% Input Current Accuracy up to 8.064 A
- ±2% 20× Adapter Current or Charge Current Output Accuracy
- Programmable Adapter Detection and Indicator
- Independent Comparator With Internal Reference
- Integrated Soft-Start .
- Integrated Loop Compensation
- AC Adapter Operating Range 5 V to 24 V
- 15-µA Off-State Battery Discharge Current
- 20-pin 3.5 mm × 3.5 mm QFN Package
- bq24707: ACOK Delay Default 1.3 s
- bq24707A: ACOK Delay Default 1.2 ms
BQ24727 pinout

| Pin | Name | Description |
|---|---|---|
| 6 | ACDET | Adapter detection input. Program the adapter valid input threshold by connecting a resistor-divider from the adapter input to the ACDET pin to the GND pin. When the ACDET pin is above 0.6 V and VCC is above UVLO, REGN LDO is present, ACOK comparator and IOUT are both active. |
| 1 | ACN | Input current-sense resistor negative input. Place an optional 0.1-µF ceramic capacitor from ACN to GND for common- mode filtering. Place a 0.1-µF ceramic capacitor from ACN to ACP to provide differential-mode filtering. |
| 5 | ACOK | AC adapter detect open-drain output. The output is pulled LOW to GND by an internal MOSFET when the voltage on the ACDET pin is above 2.4 V, voltage on the VCC pin is above UVLO and voltage on the VCC pin is 245 mV above the voltage on the SRN pin, indicating a valid adapter is present to start char |
| 2 | ACP | Input current-sense resistor positive input. Place a 0.1-µF ceramic capacitor from ACP to GND for common-mode filtering. Place a 0.1-µF ceramic capacitor from ACN to ACP to provide differential-mode filtering. |
| 17 | BTST | High-side power MOSFET driver power supply. Connect a 0.047-µF capacitor from BTST to PHASE, and a bootstrap Schottky diode from REGN to BTST. |
| 4 | CMPIN | Input of independent comparator. The comparator has one 50-kΏ series resistor and one 2000-kΏ pulldown resistor. Program CMPIN voltage by connecting a resistor-divider from the IOUT pin to the CMPIN pin to the GND pin for adapter or charge current comparison or from the SRN pin to the CMPIN pin to t |
| 3 | CMPOUT | Open-drain output of independent comparator. Place a 10-kΩ pullup resistor from CMPOUT to pullup supply rail. Internal reference is 0.6 V or 2.4 V, selectable by SMBus command Charge Option(). When CMPIN is above the internal reference, CMPOUT goes HIGH. Place a resistor between CMPIN and CMPOUT to p |
Absolute maximum ratings
| Parameter | Value | Unit |
|---|---|---|
| Voltage | ACDET, SDA, SCL, LODRV, REGN, IOUT, ILIM, ACOK, IFAULT, CMPIN, | –0.3 7 |
| Maximum difference | SRP–SRN, ACP–ACN | –0.5 0.5 |
| Junction temperature, TJ | –40 155 | °C |
| Storage temperature, Tstg | –55 155 | °C |
BQ24727 applications
- Portable Notebook Computers, UMPCs, Ultra-Thin Notebooks, and Netbooks
- Enhanced Safety: OCP, OVP,FET Short
- Personal Digital Assistants
- Handheld Terminals
- Industrial and Medical Equipment
- Portable Equipment
Comments 0
Leave a comment