Skip to content

BQ738 Datasheet – Battery SMBus Charge Controller

1-4 Cell Li+ Battery SMBus Charge Controller

Published Updated 47 views Report an error
Package QFN-20 Type
BQ738-IC

BQ738 overview

The BQ738 is a 1-4 Cell Li+ Battery SMBus Charge Controller made by Texas Instruments, supplied in a QFN-20 Type package. The absolute maximum ratings table on this page lists the 10 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the BQ738 pinout and maximum ratings, with the full datasheet PDF to preview below or download.

The bq24735 device is a high-efficiency, synchronous Driven by Internal Charge Pumps battery charger, offering low component count for space-constrained, multi chemistry battery charging applications. The bq24735 device supports turbo boost by allowing battery discharge energy to the system when system power demand is temporarily higher than the adapter maximum power level so the adapter will not crash.

The bq24735 device uses two charge pumps to separately drive N-channel MOSFETs (ACFET, RBFET, and BATFET) for automatic system power source selection.

SMBus controlled input current, charge current, and charge voltage digital-to-analog converters (DACs) allow for very high-regulation accuracies that can be easily programmed by the system power management microcontroller

Datasheet

bq24735-datasheet.pdf
Format PDFSize 2.4 MBLanguage EN
Third-party / unverified source

BQ738 features

  • Adapter and Battery Provide Power to System Together to Support Intel® CPU Turbo Boost Mode
  • SMBus Host-Controlled NMOS-NMOS Synchronous Buck Converter With Programmable
  • Automatic N-Channel MOSFET Selection of System Power Source From Adapter or Battery system power management microcontroller.
  • Enhanced Safety Features for Overvoltage Protection, Overcurrent Protection, Battery, Inductor and MOSFET Short-Circuit Protection
  • Programmable Input Current, Charge Voltage, Charge Current Limits
  • ±0.5% Charge Voltage Accuracy up to 19.2 V
  • The bq24735 device uses two charge pumps to
  • ±3% Charge Current Accuracy up to 8.128 A
  • separately drive N-channel MOSFETs (ACFET,
  • ±3% Input Current Accuracy up to 8.064 A
  • ±2% 20× Adapter Current or Charge Current
  • Programmable Battery Depletion Threshold, and Battery LEARN Function
  • Programmable Adapter Detection and Indicator
  • Integrated Loop Compensation and Soft Start
  • Real-Time System Control on ILIM Pin to Limit Charge Current
  • AC Adapter Operating Range: 4.5 V to 24 V
  • 5-µA Off-State Battery Discharge Current
  • 0.65 mA (0.8 mA Max) Adapter Standby Quiescent Current

BQ738 pinout

BQ738 pinout diagram
PinNameDescription
6ACDETAdapter detection input. Program adapter valid input threshold by connecting a resistor divider from adapter input to ACDET pin to GND pin. When ACDET pin is above 0.6 V and VCC is above UVLO, REGN LDO is present, ACOK comparator and IOUT are both active.
4ACDRVCharge pump output to drive both adapter input N-channel MOSFET (ACFET) and reverse blocking N-channel MOSFET (RBFET). ACDRV voltage is 6 V above CMSRC when voltage on ACDET pin is between 2.4 V and 3.15 V, voltage on VCC pin is above UVLO and voltage on VCC pin is 275 mV above voltage on SRN pin so
5ACOKAC adapter detection open-drain output. It is pulled HIGH to external pullup supply rail by external pullup resistor when voltage on ACDET pin is between 2.4 V and 3.15 V, and voltage on VCC is above UVLO and voltage on VCC pin is 275 mV above voltage on SRN pin, indicating a valid adapter is presen
1ACNInput current-sense resistor negative input. Place an optional 0.1-µF ceramic capacitor from ACN to GND for common-mode filtering. Place a 0.1-µF ceramic capacitor from ACN to ACP to provide differential-mode filtering.
2ACPInput current-sense resistor positive input. Place a 0.1-µF ceramic capacitor from ACP to GND for common-mode filtering. Place a 0.1-µF ceramic capacitor from ACN to ACP to provide differential-mode filtering.
11BATDRVCharge pump output to drive battery-to-system N-channel MOSFET (BATFET). BATDRV voltage is 6 V above SRN to turn on BATFET to power the system from battery. BATDRV voltage is SRN voltage to turn off BATFET to power system from AC adapter. Place a 4-kΩ resistor from BATDRV to the gate of BATFET limit
17BTSTHigh-side power MOSFET driver power supply. Connect a 0.047-µF capacitor from BTST to PHASE, and a bootstrap Schottky diode from REGN to BTST.
3CMSRCACDRV charge pump source input. Place a 4-kΩ resistor from CMSRC to the common source of ACFET (Q1) and RBFET (Q2) limits the inrush current on CMSRC pin.
14GNDIC ground. On PCB layout, connect to analog ground plane, and only connect to power ground plane through the power pad underneath IC.
18HIDRVHigh-side power MOSFET driver output. Connect to the high-side N-channel MOSFET gate.

Absolute maximum ratings

ParameterValueUnit
VoltageMin SRN, SRP, ACN, ACP, CMSRC, VCC / Max –0.330
PHASEMin –2 / Max 30
ACDET, SDA, SCL, LODRV, REGN, IOUT, ILIM, ACOKMin –0.3 / Max 7
BTST, HIDRV, ACDRV, BATDRVMin –0.3 / Max 36
LODRV (2% duty cycle)Min –4 / Max 7
HIDVR (2% duty cycle)Min –4 / Max 36
PHASE (2% duty cycle)Min –4 / Max 30
Maximum difference voltageMin SRP–SRN, ACP–ACN / Max –0.50.5
Junction temperature, TJMin –40 / Max 155°C
Storage temperature, TstgMin –55 / Max 155°C

BQ738 applications

  • Portable Notebook Computers, UMPC, Ultra-Thin Notebooks, and Netbooks
  • Handheld Terminals
  • Industrial and Medical Equipment
  • Portable Equipment

BQ738 datasheet PDF preview

PDF · 2.4 MB

Comments 0

Leave a comment