EGLXT973E Datasheet – 2-port 10/100 Ethernet Transceiver
Low-power, 2-port 10/100 Ethernet Transceiver
EGLXT973E overview
The EGLXT973E is a Low-power, 2-port 10/100 Ethernet Transceiver made by Intel, supplied in a PQFP 100 Pin type package. The absolute maximum ratings table on this page lists the 3 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the EGLXT973E pinout and maximum ratings, with the full datasheet PDF to preview below or download.
The LXT973 is an IEEE-compliant, 2-port, Fast Ethernet PHY transceiver that directly supports both 100BASE-TX and 10BASE-T applications. Each port provides a Media Independent Interface (MII) for easy attachment to 10 and 100 Mbps Media Access Controllers (MACs). The device also provides a pseudo-ECL interface per port for use with 100BASE-FX fiber networks. The LXT973 incorporates the auto MDIX feature, allowing it to automatically switch twisted- pair inputs and outputs.
The LXT973 is an ideal building block for systems that require two Ethernet ports, such as Internet Protocol (IP) Telephones, Twisted-Pair (TX)-to-Fiber (FX) converter modules, and for telecom applications, such as Telecom Central Office (TCO) and Customer Premise Equipment (CPE) devices. The LXT973 supports full-duplex operation at both 10 and 100 Mbps. Its operating modes can be set using auto-negotiation, parallel detection, or manual control.
Datasheet
EGLXT973E features
- Dual-port Fast Ethernet PHY
- 2.5V Operation
- 3.3V operation I/O compatibility
- Low power consumption; 250 mW per port typical
- Full 2-port MII interface with extended registers
- Auto MDI/MDIX switch over capability
- Signal Quality Error (SQE) enable/disable
- 100BASE-FX fiber-optic capability on both ports
- Integrated transmit and receive termination resistors
- Supports both auto-negotiation systems and legacy systems without auto- negotiation capability
- Support for Next Page
- 20 MHz Register Access
- Configurable via MDIO port or external control pins
- Integrated termination resistors
- 100-pin Plastic Quad Flat Package (PQFP)
- — LXT973QC - Commercial (0° to 70°C ambient).
- — LXT973QE - Extended (-40° to +85°C ambient).
EGLXT973E pinout

| Pin | Name | Description |
|---|---|---|
| 44 43 42 39 | TXD0_3 TXD0_2 TXD0_1 TXD0_0 | Transmit Data. TXD0_n is a bundle of parallel data signals driven by the MAC controller, which TXD0<3:0> transition synchronously with respect to the TXCLK0. TXD0<0> is the least significant bit. TXD0<3:0> are monitored in normal mode only. |
| 38 | TXEN0 | Transmit Enable. The MAC asserts TXEN0 when it drives data on TXD0n. This signal must be synchronized to TXCLK0. |
| 36 | TXER0 | Transmit Error. TXER0 is a 100 Mbps only signal. The MAC asserts this input when an error has occurred in the transmit data stream. When operating at 100 Mbps, the LXT973 responds by sending "H symbols” on the line. In Symbol mode, this pin acts as TXD0_4. |
| 37 | TXCLK0 | Transmit Clock. TXCLK0 is sourced by the LXT973 in both 10 Mbps and 100 Mbps modes. 2.5 MHz for 10 Mbps operation 25 MHz for 100 Mbps operation. |
| 29 30 3132 | RXD0_3 RXD0_2 RXD0_1 RXD0_0 | Receive Data.The LXT973 drives received data on these outputs, synchronous to RXCLK0. |
| 33 | RXDV0 | Receive Data Valid. The LXT973 asserts this signal when it drives valid data on RXD0n. This output is synchronous to RXCLK0. |
| 35 | RXER0 | Receive Error. The LXT973 asserts this output when it receives invalid symbols from the network. RXER0 is synchronous to RXCLK0. In Symbol mode, this pin acts as RXD0_4. |
| 34 | RXCLK0 | Receive Clock. RXCLK0 is sourced by the LXT973 in both 10 Mbps and 100 Mbps modes. 2.5 MHz for 10 Mbps operation 25 MHz for 100 Mbps operation. |
| 45 | COL0 | Collision Detected. The LXT973 asserts this output when a collision is detected. This output remains High for the duration of the collision. COL0 is asynchronous and is inactive during full-duplex operation. |
| 46 | CRS0 | Carrier Sense. During half-duplex operation, the LXT973 asserts this output when either the transmit or receive medium is non-idle. During full-duplex operation, CRS0 is asserted only when receive medium is non-idle. |
Absolute maximum ratings
| Parameter | Symbol | Value | Unit |
|---|---|---|---|
| Supply Voltage1,2 | VCCA, Vcc3 | Min -0.3 / Max 3.0 | V |
| VCCPECL, VCCIO3 | -0.3 | Min 4.0 / Max V | |
| Storage Temperature | TST | Min -65 / Max +150 | ºC |
EGLXT973E applications
- VoIP Telephone Handsets
- Media Converter Fiber-to-Twisted-Pair
- Fiber-to-Twisted-Pair
- Internet Access Devices Cable Modem, ADSL Modem
- Cable Modem, ADSL Modem
- Ethernet Backplane Connections
Comments 0
Leave a comment