Skip to content

H27UCG8T2BTR-BC Datasheet - 64Gb MLC NAND Flash Memory

F20 64Gb MLC NAND Flash Memory

Published Updated 27 views Report an error
Package TSOP 48 Pin Type
H27UCG8T2BTR-BC-IC

H27UCG8T2BTR-BC overview

The H27UCG8T2BTR-BC is an F20 64Gb MLC NAND Flash Memory, supplied in a TSOP 48 Pin Type package. The absolute maximum ratings table on this page lists the 7 limits from the manufacturer's datasheet that must not be exceeded. This page brings together the H27UCG8T2BTR-BC pinout and maximum ratings, with the full datasheet PDF to preview below or download.

The product part No. H27UCG8T2BTR-BC is a single 3.3V 64Gbit NAND flash memory. The Device contains 2 planes in a single die. Each plane is made up of the 1066 blocks. Each block consists of 256 programmable pages. Each page contains 17,664 bytes. The pages are subdivided into an 16,384 byte main data storage area with a spare 1,280 byte district.

Datasheet

h27ucg8t2btr-datasheet.pdf
Format PDFSize 3.8 MBLanguage ENRevision Rev. 0.1, Oct. 2012
Third-party / unverified source

H27UCG8T2BTR-BC features

  • Multi Level Cell (MLC) Technology
  • Power Supply Voltage VCC / VCCq= 2.7V ~ 3.6V
  • VCC / VCCq= 2.7V ~ 3.6V
  • Organization
  • Page Size : 16,384 + 1,280(Spare) bytes
  • Block Size : 4M + 320K bytes, 256pages
  • Plane Size : 1024 + 42(Extended) blocks
  • Device Size : 2048 + 84(Extended) blocks
  • Page Read Time Random Read Time (tR) : 65us Sequential Access (tRC/tWC) : 16ns (Min.)
  • Random Read Time (tR) : 65us
  • Sequential Access (tRC/tWC) : 16ns (Min.)
  • Page Write Time Page Program Time : 1500(Typ.)
  • Page Program Time : 1500(Typ.)
  • Block Erase Time Block Erase Time : 5.0ms (Typ.)
  • Block Erase Time : 5.0ms (Typ.)
  • Hardware Data Protection Program/Erase locked during power transitions
  • Program/Erase locked during power transitions
  • Package Package type : TSOP Chip count : SDP Pin (Ball) count : 48 Size : 12mm x 20mm x 1.2mm
  • Package type : TSOP
  • Chip count : SDP
  • Pin (Ball) count : 48
  • Size : 12mm x 20mm x 1.2mm
  • Electronic Signature
  • 1st cycle : Manufacturer code
  • 2nd cycle : Device code
  • 3rd cycle : Internal chip number, Cell type, Number of simultaneously programmed pages
  • 4th cycle : Page size, Block size, Organization, Spare size
  • 5th cycle : Multi-plane information
  • 6th cycle : Technology, EDO, Interface
  • Reliability TBD
  • TBD

H27UCG8T2BTR-BC pinout

H27UCG8T2BTR-BC pinout diagram
NameDescription
I/O 0― I/O 7DATA INPUTS/OUTPUTS The I/O pins is used to COMMAND LATCH cycle, ADDRESS INPUT cycle, and DATA in-out cycles during read / write operations. The I/O pins float to High-Z when the device is deselected or the outputs are disabled.
CLECOMMAND LATCH ENABLE This input activates the latching of the I/O inputs inside the Command Register on the Rising edge of Write Enable (WE#).
ALEADDRESS LATCH ENABLE This input activates the latching of the I/O inputs inside the Address Register on the Rising edge of Write Enable (WE#).
CE#CHIP ENABLE This input controls the selection of the device. When the device is busy, CE# low does not deselect the memory. The device goes into Stand-by mode when CE# goes High during the device is in Ready state. The CE# signal is ignored when device is in Busy state, and will not enter Standby mo
WE#WRITE ENABLE This input acts as clock to latch Command, Address and Data. The I/O inputs are latched on the rise edge of WE#.
RE#READ ENABLE The RE# input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid tREA after the falling edge of RE# which also increments the internal column address counter by one.
WP#WRITE PROTECT The WP# pin, when Low, provides a hardware protection against undesired write operations. Hardware Write Protection is activated when the Write Protect pin is low. In this condition modify operation do not start and the content of the memory is not altered. Write Protect pin is not lat
R/B#READY / BUSY The Ready/Busy output is an Open Drain pin that signals the state of the memory.
VCCQSUPPLY VOLTAGE FOR I/O BUFFER
VSSQGROUND FOR I/O BUFFER
VCCSUPPLY VOLTAGE The VCC supplies the power for all the operations. (Read, Write, and Erase).
VSSGROUND
NCNO CONNECTED

Absolute maximum ratings

ParameterSymbolValueUnit
Ambient Operating Temperature (Commercial Temperature Range)TA0 to 70℃
-25 to 85Ambient Operating Temperature (Extended Temperature Range)℃
-40 to 85Ambient Operating Temperature (Industrial Temperature Range)℃
Temperature Under BiasTBIAS-50 to 125℃
Storage TemperatureTSTG-65 to 150℃
Input or Output VoltageVIO-0.6 to 4.6V
Supply VoltageVCC-0.6 to 4.6V

H27UCG8T2BTR-BC applications

  • NAND Flash Memory
  • Solid-State Drives (SSDs)
  • Embedded Systems
  • Data Storage
  • Consumer Electronics

H27UCG8T2BTR-BC datasheet PDF preview

PDF · 3.8 MB

Comments 0

Leave a comment