Skip to content

IT8152G Datasheet – RISC to PCI Companion Chip

Published Updated 35 views Report an error
Package 208-pin PQFP and 208-pin LBGA Type
IT8152G-IC

IT8152G overview

The IT8152, an advanced RISC-to-PCI companion chip that supports SA1110 32-bit RISC microprocessor interface, is especially designed for the main applications in Datacomm, Telecomm, and Internet Appliances and Networking devices. This companion chip interfaces directly to RISC processors, and provides a bridge to link host bus and PCI bus. It also provides a Shared Memory (SDRAM) Controller, Low Pin Count (LPC) Host Controller, Interrupt Controller, DMA Controller, Timers, USB Host Controller, Digital AC9’ 7 Controller, GPIO Controller and Power Management.

Paired with Intels’ SA1110 RISC microprocessor interface, the IT8152 provides a low cost, high performance host to PCI bridge function for any system applications in Datacomm/Telecomm products. The IT8152 is available in two packages: 208-pin PQFP and 208-pin LBGA.

Datasheet

it8152f-datasheet.pdf
Format PDFSize 519 KBLanguage EN
Third-party / unverified source

IT8152G features

  • CPU Interface Supports INTEL Strong Arm Series SA1110 32-bit RISC microprocessor interface
  • Supports INTEL Strong Arm Series SA1110 32-bit RISC microprocessor interface
  • Shared SDRAM Controller
  • Supports 16Mb, 64Mb, 128Mb, 256Mb SDRAM
  • Supports up to 64MB Memory
  • 32-bit data bus interface
  • Supports one bank of SDRAM shared with SA1110 microprocessor interface SDRAM controller
  • Provides deep levels of PCI to SDRAM buffers for burst transfer
  • Up to 96 MHz bus operation
  • PCI Bus Controller
  • Supports PCI rev. 2.1 specification
  • Provides CPU to PCI buffers for burst transfer
  • PCI bus arbiter built in
  • Supports up to 4 individual external bus master devices
  • Supports CLKRUN# signal function
  • 33 MHz bus operation
  • Interrupt Controller
  • Supports one maskable interrupt to RISC processor
  • Interrupt order is controlled by software
  • Registers support interrupts masking and unmasking
  • Chaining DMA Controller
  • Four independent software DMA channels
  • Supports chaining mode and non-chaining mode
  • Supports both PCI memory address and I/O address
  • Supports rotating and fixed priority types
  • Supports DMA transfers of unaligned address
  • Timers
  • 4-channel 24-bit auto-reloaded timer with pre-scale (1,1/16,1/256) for dividing CPU clock
  • Supports the interrupt generation whenever the timers’ count reaches 0
  • Low Pin Count (LPC) Host Controller
  • Compliant with Intel LPC Interface Specification Rev. 1.0 (Sept. 29, 1997)
  • Supports Serial IRQ Protocol
  • Shared with GPIO pins
  • Digital AC’97 Controller Directly interfaced to AC9‘ 7 CODEC for controlling voice data to the speaker or from the microphone
  • Directly interfaced to AC9‘ 7 CODEC for controlling voice data to the speaker or from the microphone
  • USB Host Controller
  • Supports two USB ports
  • Supports device bandwidth of 12 Mbps or 1.5 Mbps
  • Supports power management mode to protect USB Bus power, and overcurrent detector to protect USB bus from abnormal overcurrent load

IT8152G pinout

IT8152G pinout diagram
PinName
153
254
355
456
557
658
759
860
961
1062
1163
1264
1365
1466
1567
1668
1769
1870
1971
2072
2173
2274
2375
2476
Show all 52 pins
PinName
2577
2678
2779
2880
2981
3082
3183
3284
3385
3486
3587
3688
3789
3890
3991
4092
4193
4294
4395
4496
4597
4698
4799
48100
49101
50102
51103
52104

IT8152G applications

  • Embedded Systems
  • Industrial Automation
  • IoT Devices
  • Communication Systems
  • Consumer Electronics

IT8152G datasheet PDF preview

PDF · 519 KB

Comments 0

Leave a comment