Arduino Nano v3.0 FT232RL Dev Board
Arduino Nano v3.0 FT232RL Dev Board overview
The Arduino Nano v3.0 FT232RL Dev Board is an electronic component. Main ratings: Microcontroller ATmega328P; Clock frequency 16 MHz; Flash memory 32 KB (2 KB allocated for the bootloader); RAM memory 2 Kilobytes. This page brings together the Arduino Nano v3.0 FT232RL Dev Board pinout and key specifications, with the full datasheet PDF to preview below or download.
Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3. x). The board is equipped with a patented FT232RL microcontroller, which acts as a link between the Nano mini USB port and the main ATmega328P controller. The heart of the Arduino Nano is the ATmega328P microcontroller, which operates from a base 5-volt standard for most ARDUINO boards and at a quartz resonator frequency of 16 megahertz, which has also proven itself well in the UNO board, widely known to the ARDUINO community.
The outputs of the board can operate in the modes of receiving and transmitting logical level values that are configured for each contact. The maximum current carrying capacity of a single digital output is 40 milliamps. Some of the digital contacts are combined with analog ones and have additional functional tools. The pinMode(), digitalWrite(), digitalRead() functions are used to interact with digital pins.
Key specifications
Datasheet
Arduino Nano v3.0 FT232RL Dev Board features
- Input/Output Pins are 22
- Analog i/p pins are 6 from A0 to A5
- 14 Digital pins
- Power consumption is 19 mA
- I/O pins DC Current is 40 mA
- Flash memory is 32 KB
- SRAM is 2 KB
- EEPROM is 1 KB
- Supports three communications like SPI, IIC, & USART
Arduino Nano v3.0 FT232RL Dev Board pinout
| Name | Description |
|---|---|
| Power | Vin: Input voltage to Arduino when using an external power source (6-12V).5V: Regulated power supply used to power the microcontroller and other components on the board.3.3V: 3.3V supply generated by the onboard voltage regulator. The maximum current draw is 50mA.GND: Ground pins. |
| Reset | Resets the microcontroller. |
| Analog Pins | Used to measure analog voltage in the range of 0-5V |
| Input/Output Pins | Can be used as input or output pins. 0V (low) and 5V (high) |
| Serial Communication Pins | Used to receive and transmit TTL serial data. |
| External Interrupts | To trigger an interrupt. |
| PWM | Provides 8-bit PWM output. |
| SPI | Used for SPI communication. |
| Inbuilt LED | To turn on the inbuilt LED. |
| IIC | Used for TWI communication. |
| AREF | To provide a reference voltage for input voltage. |
Arduino Nano v3.0 FT232RL Dev Board specifications
| Microcontroller | ATmega328P |
|---|---|
| Clock frequency | 16 MHz |
| Flash memory | 32 KB (2 KB allocated for the bootloader) |
| RAM memory | 2 Kilobytes |
| EEPROM-memory | 1 Kilobyte |
| Operating voltage | 5 volts |
| Input voltage, VIN | 7-12 volts |
| Input voltage maximum, VIN | 6-20 volts |
| Digital inputs/outputs | 19 |
| Variable voltage outputs, PWM | 6 |
| Analog inputs, ADC | 8 |
| Maximum continuous input/output current | 40mA, recommended: 20mA |
| Maximum DC output current 3.3V | 50mA |
| USB connector | miniUSB Type-B |
| LED indication | power, serial UART (RX and TX), pin D13 |
| Miniature dimensions | 45 x 18 mm |
| Module weight | 6 grams |
Arduino Nano v3.0 FT232RL Dev Board applications
- IoT Applications
- DIY Projects
Comments 0
Leave a comment